Author Topic: Kiwi 1971 Cuda.  (Read 7837 times)

Online 70chall440

  • Sr. Resident
  • ******
  • Posts: 5554
Re: Kiwi 1971 Cuda.
« Reply #135 on: July 28, 2019 - 12:18:22 pm »
One step at a time...  :bigsmile:

Good progress
Current Mopar
70 Challenger RT 440-6 EFI, 73 Cuda 416-6 EFI
05 Hemi Durango, 01 Ram 4x4, 14 Ram 2500 4X4, 10 PCP Challenger 6 spd RT, 01 Viper GTS ACR, 52 B3B w/330 Desoto Hemi, 70 Hemi RR (under const)
Past Mopars
9 x Challengers. AAR Cuda, 4 RR, 2 GTX, 4 Chargers, etc... (too many to list)




Offline tony 73

  • Jr. Member
  • **
  • Posts: 309
Re: Kiwi 1971 Cuda.
« Reply #136 on: July 28, 2019 - 05:06:41 pm »
Cheers mate.

Heater box done, was fun unwrapping the new heater core which had been stored away. looking forward to opening more part boxes.


Online 70chall440

  • Sr. Resident
  • ******
  • Posts: 5554
Re: Kiwi 1971 Cuda.
« Reply #137 on: July 29, 2019 - 12:10:19 am »
Cheers to you.

Looks very nice, will look good in the car.
Current Mopar
70 Challenger RT 440-6 EFI, 73 Cuda 416-6 EFI
05 Hemi Durango, 01 Ram 4x4, 14 Ram 2500 4X4, 10 PCP Challenger 6 spd RT, 01 Viper GTS ACR, 52 B3B w/330 Desoto Hemi, 70 Hemi RR (under const)
Past Mopars
9 x Challengers. AAR Cuda, 4 RR, 2 GTX, 4 Chargers, etc... (too many to list)

Offline tony 73

  • Jr. Member
  • **
  • Posts: 309
Re: Kiwi 1971 Cuda.
« Reply #138 on: August 06, 2019 - 07:27:11 am »
Thanks mate. Just need to get  paint on body and these parts can be refitted.

Steering column 95% finished, crush can needs to be secured fully.

Online 70chall440

  • Sr. Resident
  • ******
  • Posts: 5554
Re: Kiwi 1971 Cuda.
« Reply #139 on: August 06, 2019 - 01:06:02 pm »
Looks good, if you haven't I would highly recommend really looking at the wiring carefully. This is one place that causes a lot of issues and it is much easier to deal with at this point. Personally I would replace the ignition switch and perhaps even the turn signal cam.
Current Mopar
70 Challenger RT 440-6 EFI, 73 Cuda 416-6 EFI
05 Hemi Durango, 01 Ram 4x4, 14 Ram 2500 4X4, 10 PCP Challenger 6 spd RT, 01 Viper GTS ACR, 52 B3B w/330 Desoto Hemi, 70 Hemi RR (under const)
Past Mopars
9 x Challengers. AAR Cuda, 4 RR, 2 GTX, 4 Chargers, etc... (too many to list)

Offline redo1973

  • Full Member
  • ***
  • Posts: 524
Re: Kiwi 1971 Cuda.
« Reply #140 on: August 11, 2019 - 10:33:16 pm »
Looks great.  I also recommend obtaining a item developed for the coupler recall to address the cap from loosening.  It is simply a 2 pronged bent piece of 1/8 rod that hooks into the spring pin and keeps the cover down and tight.  It is installed once the full steering shaft is installed.  It's only around $10 and easily found on ebay.https://www.ebay.com/itm/Mopar-A-B-E-Body-66-73-3-Steering-Coupler-Retainer-Clamp-STAINLESS-DMT-2996935/291757502737?hash=item43ee1a3111:g:ADQAAOSwhjNbX~wl

Offline tony 73

  • Jr. Member
  • **
  • Posts: 309
Re: Kiwi 1971 Cuda.
« Reply #141 on: August 17, 2019 - 05:44:27 pm »
Thanks for the input guys. Have had good look at the wiring and happy with what I saw. I have not fully secured the crush can down so will have another look on next wet day when I need an inside job. I do have a new turn signal cam which I should fit.

Like the look of the clamp. Car came with a steering coupler rebuild kit which I used . Reused the rubber boot as new one bit tight. No harm getting the clamp.

Pulled front seats apart to get ride of rust and mouse house material. May media blast if manual labour doesn't work.

Got nugget in housing and odd bit reattached.

Got new U joints for drive shaft so pushed old ones out, was easier than expected .

Mate and I pulled Tach gauge apart and replaced old circuit board with one from rt-eng., needs adjustment as was reading 200rpm over when tested in his Challenger which had a rev-n-nator ignition box on the firewall. Need to visit another friend some time soon.

So many small jobs to complete.

Online 70chall440

  • Sr. Resident
  • ******
  • Posts: 5554
Re: Kiwi 1971 Cuda.
« Reply #142 on: August 18, 2019 - 12:37:23 am »
Its the small things that add up and is so nice when it all comes together. Great work.
Current Mopar
70 Challenger RT 440-6 EFI, 73 Cuda 416-6 EFI
05 Hemi Durango, 01 Ram 4x4, 14 Ram 2500 4X4, 10 PCP Challenger 6 spd RT, 01 Viper GTS ACR, 52 B3B w/330 Desoto Hemi, 70 Hemi RR (under const)
Past Mopars
9 x Challengers. AAR Cuda, 4 RR, 2 GTX, 4 Chargers, etc... (too many to list)

Offline redo1973

  • Full Member
  • ***
  • Posts: 524
Re: Kiwi 1971 Cuda.
« Reply #143 on: August 20, 2019 - 09:11:06 pm »
Fun times.  The details really pull the whole project together for a great package.  Hang in there, it must be very exciting as you are checking off the list of items.